유리섬유직물에 대한 수지의 젖음성 평가
Wettability Evaluation of Resin on the Glass Fabric
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
에폭시 수지와 유리섬유직물 간의 젖음성을 분석하였다. 에폭시 수지와 산무수물 경화제의 혼합비는 당량비 1:0.5, 1:1, 1:1.2로 하였고, 촉매는 혼합된 수지의 0.1wt%로 첨가하였다. DSC 경화거동분석 결과 이 혼합 수지는 상온에서 함침이 가능하였다. 혼합 수지에 대해 유리평판에 놓여진 유리섬유직물 위에 수지 한 액적(방울)을 투하 후 시간에 따른 접촉각 변화를 측정하였다. 또한, 일정량의 에폭시 수지 액적을 투하시켜 시간에 따른 젖음면적 변화를 측정하였다. 접촉각, 액적높이, 순수 젖음면적, 젖음계수를 측정함으로써 유리섬유직물에 대한 에폭시 수지의 젖음성을 비교 평가하였다. 그 결과 당량비 1:1.2에서 유리섬유직물에 대한 젖음성이 가장 우수하였다.
Abstract
Analysis of wettability between epoxy resin and glass fabric was studied. The mixing ratios of epoxy resin and anhydride hardener were varied as 1:0.5, 1:1 and 1:1.2. Catalyst content was fixed as 0.1wt% of the mixed resin. A curing analysis by differential scanning calorimeter(DSC) showed a possible impregnation of the mixed resin at the room temperature. An effective contact angle of the mixed epoxy resin drop onto the glass fabric being preset on a flat glass plate was measured as a function of time. The wet area of the epoxy resin drop was also measured. Behaviors of the contact angle, the droplet height, the neat wet area and the coefficient of wettability were used to evaluate the wettability of the epoxy resin onto the glass fabric. It was concluded that the equivalent ratio of 1:1.2 was the most suitable for the wettability.
참고문헌 (16)
- N. C. W. Judd, "Voids and their effects on the mechanical properties of composites-appraisal", SAMPLE Journal (1978)
- S. F. M. Almeida, "Effect of void content on the strength of composite laminates", Composite Structures, 28(2), pp.139~148 (1994)
- "1995", 7(1)
- Neil Pearcea, "A study of the effects of convergent flow fronts on the properties of fibre reinforced composites produced by RTM", Composites part A, 29A, pp.141~152 (1997)
- 이찬용, "접촉각 측정 원리를 이용한 새로운 사이즈도 측정기(제1보)-자동 접촉각 측정 원리의 개발", 펄프종이기술, 35(3), pp.43~52 (2003), 한국펄프·종이공학회
- John P. Coulter, "Resin Impregnation During the Manufacturing of Composite Materials Subject to Prescribed Injection Rate", Journal of Reinforced Plastics and Composites, 7(3), pp.200~219 (1988)
- 박수진, "열잠재성 촉매 개시제를 이용한 에폭시 수지의 경화거동 및 열안정성", 한국복합재료학회지, 17(5), pp.47~53 (2004), 한국복합재료학회
- D. S. Lee, "Cure Behavior of High Performance Epoxy", Polysulfone Blends (Ⅰ), 1996, pp.20(3), 403~411
- D. S. Lee, "Cure Behavior of High Performance Epoxy", Polysulfone Blends (Ⅱ), 1996, pp.20(3), 412~418
- Measuring and Analyzing with ease (iSolution Lite), "iMTechnology (Image & Microscope Technnology)", ~ (2001)
- C. S. Wang, "Reducing Fiber Readout of Structural Composite Panels", Journal of Reinforced Plastics and Composites, 28(19), pp.2377~2386 (2009)
- K. J. Ahn, "Simultaneous measurements of permeability and capillary pressure of thermosetting matrices in woven fabric reinforcements", Polymer Composites, 12(3), pp.146~152 (1991)
- J. G. Williams, "Liquid flow through aligned fiber beds", Polymer Engineering & Science, 14(6), pp.413~419 (1974)
- C. H. Lee, "An Experimental Study on the Effect of Capillary Pressure on the Void Formation in Resin Transfer Molding Process", The Korean Journal of Rheology, 10(4), pp.185~194 (1998)
- G. W. Lee, "Experimental and Numerical Studies on the Flow Characteristics in Resin Transfer Molding Process", The Korean Journal of Rheology, 7(4), pp.139~149 (1995)
- S. T. Nam, "Effect of Physical Prooerties of Polymer Solution on the Thickness if Ultrathin Membrane Prepared by Water Casting Method", J. of Korean Ind. & Eng. Chemistry, 9(2), pp.200~206 (1998)