Test and Analysis of Triaxially Braided Composite Circular Arch under Three-Point Bending
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
In this paper, the buckling behavior of triaxially braided circular arch with monosymmetric open section subjected to three-point bending was studied experimentally and numerically. First, test specimens were manufactured using vacuum assisted resin transfer molding (VARTM). Then the specimen was tested under three-point bending to determine the ultimate buckling strength. Before performing the numerical analysis, effective material properties of the braided composite were obtained through micro-meso scale analysis virtual testing validated with available test results. Then linear buckling analysis and geometrically non-linear post buckling analysis, established to simulate the test setup, were performed to study the buckling behavior of the composite frame. Analysis results were compared with experimentally obtained ones for verification. The effect of manufacturing defects of tow misalignment, irregular surface and resin rich region, and uncertainties during test setup were studied using numerical models. From the numerical analyses performed it was observed that both manufacturing defect and uncertainties had effect on the buckling behavior and strength.
Abstract
In this paper, the buckling behavior of triaxially braided circular arch with monosymmetric open section subjected to three-point bending was studied experimentally and numerically. First, test specimens were manufactured using vacuum assisted resin transfer molding (VARTM). Then the specimen was tested under three-point bending to determine the ultimate buckling strength. Before performing the numerical analysis, effective material properties of the braided composite were obtained through micro-meso scale analysis virtual testing validated with available test results. Then linear buckling analysis and geometrically non-linear post buckling analysis, established to simulate the test setup, were performed to study the buckling behavior of the composite frame. Analysis results were compared with experimentally obtained ones for verification. The effect of manufacturing defects of tow misalignment, irregular surface and resin rich region, and uncertainties during test setup were studied using numerical models. From the numerical analyses performed it was observed that both manufacturing defect and uncertainties had effect on the buckling behavior and strength.
참고문헌 (20)
- Li, X., "Finite-element Model for Failure Study of Two-dimensional Triaxially Braided Composite", Journal of Aerospace Engineering, 24(2), pp.170~180 (2010)
- Xu, L., "Prediction of Material Properties of Biaxial and Triaxial Braided Textile Composites", Journal of Composite Materials, 46(18), pp.2255~2270 (2012)
- Kosztowny, C. J., "Buckling and Post-Buckling Behavior of Unitized, Stiffened Tri-Axially Braided Composite Textile Plates", Proceeding of the 55th SDM Conference (2014)
- Potdar, S. A., "Design Method Prediction for Flexural Torsional Buckling Re-sistance of Steel Circular Arches-Box-Section", Journal of Modern Engineering Research, 6(7), pp.8~14 (2016)
- Dou, C., "Experimental Investigation into Flexural-torsional Ultimate Resistance of Steel Circular Arches", Journal of Structural Engineering, 141(10), pp.1~12 (2015)
- Guo, Y. L., "An Experimental Study on Out-of-plane Inelastic Buckling Strength of Fixed Steel Arches", Engineering Structures, 98, pp.118~127 (2015)
- Barbero, E., "Euler Buckling of Thin-walled Composite Columns", Thin-walled Structures, 17(4), pp.237~258 (1993)
- Qiao, P., "Flexural–torsional Buckling of Fiber-reinforced Plastic Composite Cantilever I-beams", Composite Structures, 60(2), pp.205~217 (2003)
- Omidvar, B., "Nonlinear FE Solution for Thin-walled Open-section Composite Beams", Journal of Structural Engineering, 122(11), pp.1369~1378 (1996)
- "ASTM E1856-13, Standard Guide for Evaluating Computerized Data Acquisition Systems Used to Acquire Data from Universal Testing Machines", ASTM International, ~ (2013)
- Hassan, N. K., "Buckling and Ultimate Failure of Thin-walled Pultruded Composite Columns", Polymers and Polymer Composites, 12(6), pp.469~481 (2004)
- Lee, J. H., "Flexural–torsional Buckling of Thinwalled I-section Composites", Computers & Structures, 79(10), pp.987~995 (2001)
- Arbelo, M. A., "Experimental and Numerical Estimation of Buckling Load on Unstiffened Cylindrical Shells Using a Vibration Correlation Technique", Thin-Walled Structures, 94, pp.273~279 (2015)
- Hosseini-Toudeshky, H., "Delamination Buckling Growth in Laminated Composites Using Layerwise-interface Element", Composite Structures, 92(8), pp.1846~1856 (2010)
- Schenk, C. A., "Buckling Analysis of Cylindrical Shells with Random Geometric Imperfections", International Journal of Non-Linear Mechanics, 38(7), pp.1119~1132 (2003)
- Sadovský, Z., "Computational Modelling of Geometric Imperfections and Buckling Strength of Cold-formed Steel", Journal of Constructional Steel Research, 78, pp.1~7 (2012)
- Mekonnen, A. A., "Effects of Defects on Effective Material Properties of Triaxially Braided Textile Composite", Submitted to International Journal of Aeronautical and Space Sciences (2019)
- "ASTM D3039", D3039M-17, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, 2017
- Alpha STAR Corporation, "MCQ-Composites Theoretical Manual" (2014), Alpha STAR Corporation
- Tsinuel N. Geleta, "Prediction of Effective Material Properties for Triaxially Braided Textile Composite", International Journal of Aeronautical and Space Sciences, 18(2), pp.222~235 (2017), 한국항공우주학회