진공백 핫 프레스 성형공정을 이용한 탄소섬유 복합재료의 제조와 공정비교
Preparing of Carbon Fiber Composites Using by Vacuum Bag Hot-press Molding Process and Comparison with the other Molding Processes
3
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
본 연구에서는 우수한 물성과 표면품질을 가지는 오토클레이브 성형공법의 비효율적인 공정을 개선하여탈 오토클레이브(Out-of-autoclave, 이하 OOA) 공정으로써 활용이 가능한 진공백 핫 프레스 공정(Vacuum bag hotpress, 이하 V-HP)을 이용하여 탄소섬유 복합재료를 제작하고 오토클레이브(Autoclave, 이하 AC) 공정과 핫 프레스공정(Hot-press, 이하 HP)으로 제작된 복합재료간 물성 및 미세구조를 분석하였으며, OOA공정으로의 가능성을확인하였다. V-HP공정을 사용한 복합재료의 인장강도는 320.6MPa로써, AC공정을 이용한 복합재료의 인장강도335.3 MPa에 상당히 근접한 물성을 보이는 것을 확인하였다. SEM을 이용한 복합재료 표면품질을 확인한 결과 VHP공정의경우, 수지내 휘발용매로 인한 기공의 제거상태가 AC공정과 비교하여 다소 낮으나 HP공정과 비교하여 상당히 우수한 표면을 가지는 것을 확인할 수 있었다.
Abstract
In this study, vacuum bag hot-press (V-HP) process can be used as an out-of-autoclave (OOA) process by improving the inefficient process of the autoclave forming method with excellent physical properties and surface quality. A carbon fiber composite was molded via V-HP process and analyzed the physical properties and microstructures between composites manufactured by autoclave (AC) process and hot-press process (HP). The tensile strength of the composite materials using the V-HP process was 320.6 MPa and the AC process samples found to be substantially close to the tensile strength of 335.3 MPa. As a result of confirming the surface quality of the composite material using SEM, it was confirmed that in the V-HP process, the removal state of pores due to volatile solvent in the resin was slightly lower than that of the AC process, but it had a considerably superior surface compared to the HP process.
참고문헌 (7)
- 김정수, "가압장치를 이용한 오토클레이브 대체 복합재료 성형공정 개발 및 분석", Composites Research, 27(6), pp.254~259 (2014), 한국복합재료학회
- Grunenfelder, L. K., "Effect of Room-temperature Out-time on Tow Impregnation in an Out-of-autoclave Prepreg", Composites : Part A, 45, pp.119~126 (2013)
- Centea, T., "A Review of Out-of-autoclave Prepregs – Material Properties, Process Phenomena, and Manufacturing Considerations", Compoistes : Part A, 70, pp.132~154 (2015)
- Thorfinnson, B., "Degree of Impregnation of Prepregs – Effects on Porosity", Proc 32nd int SAMPE Symp. Anaheim, CA: Society for the Advancement of Material and Process Engineering, pp.9~ (1987)
- Juska, T. D., "The New Infusion: oven Vacuum Bag Prepreg Fabrication", Proc SAMPE 2009 Conf. Baltimore, MD: Society for the Advancement of Material and Process Engineering (2009)
- Yoon, B. I., "Effect of Fiber Volume Fraction on the Mechanical Properties in Carbon Fiber-Epoxy Composites", Polymer Society of Korea, 12(7), pp.619~626 (1988)
- Moon, Y. J., "A Study on the Shape of the Fiber-reinforced Composite Material According to the Durability and Mechanical Properties", Ph. D, pp.2011