3D 프린팅용 모르타르의 초기재령 수축거동 평가를 위한 실험적 연구
Experimental Study for Evaluating Early Age Shrinkage of Mortar for 3D Printing
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
이 연구는 적층 시공 시 타설 초기부터 외기에 직접 노출되는 조건을 모사하여 밀봉조건과 노출조건에 따른 수축거동을 100일 이상 실험적으로 분석하였다. 결합재 치환에 따른 수축거동 분석을 위해 1종 시멘트, 플라이애시, 실리카흄을 사용하여 동일한 조건에서 길이변화율을 측정하였다. 혼화제 사용이 수축거동에 미치는 영향을 분석하기 위해 적층 시공 시 사용되는 셀룰로오스계 점도조절제와 유지계 수축저감제를 사용하였다. 표면노출양생 시 초기 수축 발생시점이 단축됐으며, 플라이애시와 실리카흄을 사용 시 수축량은 양생조건에 따라 OPC100 배합 대비 60 – 110% 증가했다. 점도조절제와 수축저감제 적용은 양생조건에 따라 최소 18%에서 최대 70% 수축량을 저감시켰다. 시험체의 온도는 양생초기 15 ℃까지 일시적으로 저하됐으며, 수축거동과 상관성을 이 연구를 통해 확인했다.
Abstract
Since the 3D printing mortar is exposed to the atmosphere immediately after printing, moisture is largely evaporated from the surface of the layer. The evaporation of moisture on the surface of the layer greatly causes drying shrinkage and increases the risk of cracking and damage to the structure due to drying shrinkage. This study experimentally evaluated the shrinkage behavior of the initial age using the mortar used for 3D printing. The change in shrinkage was evaluated by comparing the shrinkage of the specimen cured by the sealing method and the atmospheric exposure method. In addition, compared with the case where type 1 cement was used 100%, the shrinkage amount was evaluated when 20% of fly ash was replaced and 10% of silica fume was used. In particular, the effect of three chemical admixtures applied using 3D printing on shrinkage was evaluated experimentally. When fly ash and silica fume were used, the shrinkage amount increased by 60 – 110% compared to the case when type 1 cement was used. The application of viscosity modifiers and shrinkage reducers reduced the shrinkage by at least 18% and at most 70% depending on the curing conditions. The temperature of the specimen temporarily decreased to 15 ℃ at the beginning of curing, and the correlation between the internal temperature of the specimen and the shrinkage behavior was observed.
참고문헌 (16)
- "ASTM C39. Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens", ~ (2020)
- "ASTM C490", C490M-21. Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete, 2021
- "ASTM C596-18. (2018). Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement", ~ (2018)
- Buswell, R. A., "Inspection Methods for 3D Concrete Printing, RILEM Bookseries", pp.790~803 (2020)
- Chen, H., "Effects of silica fume and Fly ash on properties of mortar reinforced with recycled-polypropylene", Construction and Building Materials, 316, pp.125887~ (2022)
- Federowicz, K., "Effect of Curing Methods on Shrinkage Development in 3D-Printed Concrete", Materials, 13(11), pp.2590~ (2020)
- 조준호, "Development of a 3D Printer for Concrete Structures: Laboratory Testing of Cementitious Materials", International Journal of Concrete Structures and Materials, 14(2), pp.305~315 (2020), 한국콘크리트학회[DOI]
- 김주형, "플라이애시 종류에 따른 플라이애시 모르타르의 특성에 대한 연구", 한국건설순환자원학회 논문집, 4(4), pp.439~445 (2016), 한국건설순환자원학회[DOI]
- Kwon, S. H., "Understanding of Drying Shrinkage and Autogeneous Shrinkage in Concrete", Magazine of the Korea Concrete Institute, 28(6), pp.22~26 (2016)
- Langan, B. W., "Effect of silica fume and flyahs on heat of hydration of Portland cement", Cement and Concrete Research, 32(7), pp.1045~1051 (2002)
- 이동규, "3D 프린팅 콘크리트용 수축저감제 개발", 한국산학기술학회논문지, 20(12), pp.37~43 (2019), 한국산학기술학회[DOI]
- 이호재, "적층공법을 적용한 시멘트계 복합재료의 수축특성", 한국구조물진단유지관리공학회 논문집, 23(6), pp.99~104 (2019), 한국구조물진단유지관리공학회
- 이호재, "건설용 3D 프린팅 압출 및 적층공정에 따른 시멘트계 복합재료의 수축 특성 영향", 한국구조물진단유지관리공학회 논문집, 24(6), pp.113~118 (2020), 한국구조물진단유지관리공학회
- Lee, H., "Experimental Study on Time-Depend_ent Changes in Rheological Properties and Flow Rate of 3D Concrete Printing Materials", Materials, 14(21), pp.6278~ (2021)
- 박종필, "콘크리트용 고성능 수축저감제 개발에 대한 기초적 특성", 한국산학기술학회논문지, 16(6), pp.4298~4307 (2015), 한국산학기술학회[DOI]
- Shi, C., "A calorimetric study of early hydration of alkali-slag cements", Cement and Concrete Research, 25(6), pp.1333~1346 (1995)