Atmospheric plasma spray 공정으로 제조된 Y2O3 코팅층의 미세조직 및 기계적 특성에 미치는 분사 각도의 영향
Effect of Spray Angle the on Microstructure and Mechanical Properties of Y2O3 Coating Layer Manufactured by Atmospheric Plasma Spray Process
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The effects of different spray angles (90°, 85°, 80°) on the microstructure and mechanical properties of a Y2O3 coating layer prepared using the atmospheric plasma spray (APS) process were studied. The powders employed in this study had a spherical shape and included a cubic Y2O3 phase. The APS coating layer exhibited the same phase as the powders. Thickness values of the coating layers were 90°: 203.7 ± 8.5 μm, 85°: 196.4 ± 9.6 μm, and 80°: 208.8 ± 10.2 μm, and it was confirmed that the effect of the spray angle on the thickness was insignificant. The porosities were measured as 90°: 3.9 ± 0.85%, 85°: 11.4 ± 2.3%, and 80°: 12.7 ± 0.5%, and the surface roughness values were 90°: 5.9 ± 0.3 μm, 85°: 8.5 ± 1.1 μm, and 80°: 8.5 ± 0.4 μm. As the spray angle decreased, the porosity increased, but the surface roughness did not show a significant difference. Vickers hardness measurements revealed values of 90°: 369.2 ± 22.3, 85°: 315.8 ± 31.4, and 80°: 267.1 ± 45.1 HV. It was found that under the condition of a 90° angle with the lowest porosity exhibited the best hardness value. Based on the aforementioned results, an improved method for the APS Y2O3 coating layer was also discussed.
Abstract
The effects of different spray angles (90°, 85°, 80°) on the microstructure and mechanical properties of a Y2O3 coating layer prepared using the atmospheric plasma spray (APS) process were studied. The powders employed in this study had a spherical shape and included a cubic Y2O3 phase. The APS coating layer exhibited the same phase as the powders. Thickness values of the coating layers were 90°: 203.7 ± 8.5 μm, 85°: 196.4 ± 9.6 μm, and 80°: 208.8 ± 10.2 μm, and it was confirmed that the effect of the spray angle on the thickness was insignificant. The porosities were measured as 90°: 3.9 ± 0.85%, 85°: 11.4 ± 2.3%, and 80°: 12.7 ± 0.5%, and the surface roughness values were 90°: 5.9 ± 0.3 μm, 85°: 8.5 ± 1.1 μm, and 80°: 8.5 ± 0.4 μm. As the spray angle decreased, the porosity increased, but the surface roughness did not show a significant difference. Vickers hardness measurements revealed values of 90°: 369.2 ± 22.3, 85°: 315.8 ± 31.4, and 80°: 267.1 ± 45.1 HV. It was found that under the condition of a 90° angle with the lowest porosity exhibited the best hardness value. Based on the aforementioned results, an improved method for the APS Y2O3 coating layer was also discussed.
참고문헌 (26)
- J. Kitamura, , J. Therm. Spray Technol, 17, pp.878~ (2008)
- R. Banal, , Mater. Trans, 46, pp.2114~ (2005)
- D. M. Kim, , J. Ceram. Soc. Japan, 120, pp.539~ (2012)
- 김민숙, "서스펜션 플라즈마 스프레이 코팅법을 이용한 이트리아 코팅막 제조와 특성", 한국결정성장학회지, 29(6), pp.359~364 (2019), 한국결정성장학회[DOI]
- J. Iwasawa, , J. Am. Ceram. Soc, 90, pp.2327~ (2007)
- P. Fauchais, , J. Thermal Spray Technol, 24, pp.1120~ (2015)
- R. Singh, , J. Mater. Eng. Perform, 21, pp.1539~ (2012)
- P. Mechnich, , J. Eur. Ceram. Soc, 33, pp.2645~ (2013)
- J. B. Song, , Coatings, 9, pp.102~ (2019)
- T. K. Lin, , Nanomaterials, 7, pp.183~ (2017)
- P. Mechnich, , J. Eur. Ceram. Soc, 33, pp.2645~ (2013)
- V. Gourlaouen, , J. Mater. Sci, 29, pp.6434~ (1994)
- H. S. An, , J. Weld. Join, 15, pp.1~ (1997)
- K. Sabiruddin, , Surf. Coat. Technol, 204, pp.3248~ (2010)
- V. Gourlaouen, , Mater. Res. Bull, 28, pp.415~ (1993)
- J. Kitamura, , J. Therm. Spray Technol, 20, pp.170~ (2011)
- C. W. Kang, , J. Therm. Spray Technol, 15, pp.118~ (2006)
- R. C. Tucker Jr., , Therm. Spray Technol, 5, pp.76~ (2013)
- B. H. Kim, , Korean J. Mater. Res, 8, pp.505~ (1998)
- H. Guo, , J. Am. Ceram. Soc, 89, pp.1432~ (2006)
- G. Montavon, , Surf. Coat. Technol, 91, pp.107~ (1997)
- S. Bose, "High Temperature Coatings", pp.155~ (2007), Butterworth-Heinemann
- H. Grünling, , J. Phys. IV, 3, pp.C7~903 (1993)
- S. H. Leigh, , Surf. Coat. Tech., 89, pp.213~ (1997)
- A. Hasui, , Trans. Nat. Res. Inst. Metals, 12, pp.9~ (1970)
- S. Dallaire, , Surf. Coat. Tech, 53, pp.129~ (1992)