피어싱 공정에서의 펀치 마모가 전단면에 미치는 영향 분석
Analysis of the effect of punch wear on shear surfaces in the piercing process
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The recent increasing application rate of advanced high-strength steel(AHSS) for automotive parts makes it difficult to ensure the durability of forming tools. Significant load and friction generated during the piercing process of AHSS increase the wear rate and the damage degree to dies. These harsh process conditions also yield product failures, such as dimensional inconsistency of pierced holes and insufficient quality of hole's sheared edge. This study analyzed the effect of punch wear on the sheared surface of pierced parts and the forming load during the piercing process. Wear-shaped punches showed approximately 20% higher piercing load than normal-shaped punches, and the rollover ratio of the sheared surface also increased. It is considered that the dull edge of wear-shaped punches does not penetrate directly into the material but shears after tensioning it in a piercing direction. In addition, wear-shaped punches experienced compressive load even after completing the piercing process during the down-stroke and tensile load during the up-stroke. This load variation is related to the smaller diameter piercing holes produced by wear-shaped punches compared to normal-shaped punches. Thus, we demonstrated the predictability of the wear level of dies through a comparative analysis of the piercing load pattern.
Abstract
The recent increasing application rate of advanced high-strength steel(AHSS) for automotive parts makes it difficult to ensure the durability of forming tools. Significant load and friction generated during the piercing process of AHSS increase the wear rate and the damage degree to dies. These harsh process conditions also yield product failures, such as dimensional inconsistency of pierced holes and insufficient quality of hole's sheared edge. This study analyzed the effect of punch wear on the sheared surface of pierced parts and the forming load during the piercing process. Wear-shaped punches showed approximately 20% higher piercing load than normal-shaped punches, and the rollover ratio of the sheared surface also increased. It is considered that the dull edge of wear-shaped punches does not penetrate directly into the material but shears after tensioning it in a piercing direction. In addition, wear-shaped punches experienced compressive load even after completing the piercing process during the down-stroke and tensile load during the up-stroke. This load variation is related to the smaller diameter piercing holes produced by wear-shaped punches compared to normal-shaped punches. Thus, we demonstrated the predictability of the wear level of dies through a comparative analysis of the piercing load pattern.
참고문헌 (8)
- 전용준, "볼트형 피에조 센서를 활용한 피어싱 펀치의 얼라인먼트 불량 검출에 관한 연구", Design & Manufacturing, 15(4), pp.51~56 (2021), 한국금형공학회[DOI]
- Ridha Hambli, "Blanking tool wear modeling using the finite element method", International Journal of Machine Tools and Manufacture, 41(12), pp.1815~1829 (2001), Elsevier BV[DOI]
- Dae-Cheol Ko, "Finite element analysis for the wear of Ti–N coated punch in the piercing process", Wear, 252(11-12), pp.859~869 (2002), Elsevier BV[DOI]
- P. Chumrum, "Experimental investigation of energy and punch wear in piercing of advanced high-strength steel sheet", Int. J. Adv. Manuf. Technol, 79, pp.1035~1042 (2015)
- Rajiv Shivpuri, "Energy release rate based approach for the wear of punches in precision blanking of high strength steel", CIRP Annals, 60(1), pp.307~310 (2011), Elsevier BV[DOI]
- D.D. Olsson, "Analysis of Pick-Up Development in Punching", CIRP Annals, 51(1), pp.185~190 (2002), Elsevier BV[DOI]
- J. Stahlmann, "Understanding and improvement of industrial production how technology paves the way for productivity", New Development in Forging Technology, 2017, pp.109~117 (2017)
- S. Y. Kim, "Monitoring of process and tool status in forging process by using bolt type piezo-sensor", Procedia Manufacturing, 15, pp.542~549 (2018)