볼 엔드밀의 헬릭스 각도에 따른 STD 11 소재의 표면 거칠기에 관한 연구
A study on the surface roughness of STD 11 material according to the helix angle of ball endmill
0
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
The ball end mill is a type of cutting tool that is widely used to process complex mold shapes including aspheric surfaces. Unlike the flat end mill in which the cutting edge is formed on the cylindrical handle, the cutting edge is formed from the cylindrical handle to the hemispherical shape, which is advantageous for processing curved shapes. However, since the cutting speed continuously changes during machining due to the helix angle of the cutting edge or the machining inclination angle, it is difficult to obtain a precise machined surface. Therefore, in this paper, machining was performed while changing the helix angle of the ball end mill and the angle of the machining slope under the same cutting conditions for STD 11 material, which is widely used as a mold material. Through this, the effect of the two variables on the roughness of the machined surface was analyzed. As a result, if the helix angle was 0 degrees, it showed the best surface roughness of Ra. 0.16 ㎛. When the helix angle was 20 degrees, the best surface roughness of Ra. 0.18 ㎛ was occurred.
Abstract
The ball end mill is a type of cutting tool that is widely used to process complex mold shapes including aspheric surfaces. Unlike the flat end mill in which the cutting edge is formed on the cylindrical handle, the cutting edge is formed from the cylindrical handle to the hemispherical shape, which is advantageous for processing curved shapes. However, since the cutting speed continuously changes during machining due to the helix angle of the cutting edge or the machining inclination angle, it is difficult to obtain a precise machined surface. Therefore, in this paper, machining was performed while changing the helix angle of the ball end mill and the angle of the machining slope under the same cutting conditions for STD 11 material, which is widely used as a mold material. Through this, the effect of the two variables on the roughness of the machined surface was analyzed. As a result, if the helix angle was 0 degrees, it showed the best surface roughness of Ra. 0.16 ㎛. When the helix angle was 20 degrees, the best surface roughness of Ra. 0.18 ㎛ was occurred.
참고문헌 (11)
- 하석재, "마이크로 금형 부품을 위한 마이크로 절삭가공 기술", Design & Manufacturing, 13(1), pp.5~12 (2019), 한국금형공학회[DOI]
- 홍광표, "Co-Cr-Mo 합금의 선삭 가공 특성에 관한 연구", Design & Manufacturing, 11(1), pp.50~54 (2017), 한국금형공학회
- 조철용, "볼 엔드밀 헬릭스 각에 따른 절삭 특성", 한국정밀공학회지, 31(5), pp.395~401 (2014), 한국정밀공학회
- Cho, C. Y., "Finishing Characteristics According to Cutting Edge Shape on the Hemisphere Part in Ball End Milling", Proceedings of the Korean Society of Precision Engineering Conference, pp.461~462 (2009)
- Ko, T. J., "Selection of Machining Inclination Angle of Tool Considering Tool Wear in High Speed Ball End Milling", J. Korean Society of Precision Engineering, 15(9), pp.135~144 (1998)
- Scherer, J., "High speed, high-precision machining with NURBS interpolation", Proceedings of 2nd International Machining & Grinding Conference, pp.709~716 (1997)
- Layne, M., "Detecting and correcting unbalance in toolholders", Proceedings of 2nd International Machining & Grinding Conference, pp.381~404 (1997)
- 맹민재, "헬릭스각의 변화에 따른 밀링공구의 변위 특성 연구", 대한기계학회논문집 A, 28(6), pp.860~866 (2004), 대한기계학회
- Jeong, H. I., "A basic study on tool life according flank wear during SKD11 material machining", KSME Spring&Autumn conference, pp.259~260 (2019)
- Choi, W. S., "Assessment of cutting ability for CBN ball end-milling", J. Korean Society of Industrial Applicaiton, 8(4), pp.227~234 (2005)
- Ashby, M. F., "Materials Selection in Mechanical Design" (2005), Elsevier Butterworth–Heinemann