중년 여성용 3D 프린팅 토르소 더미를 사용한 시판 바디쉐이퍼 제품의 의복압 분석
Analysis of Clothing Pressure of Commercial Body Shapers using 3D Printed Torso Dummy for Middle-aged Women
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study measured and analyzed clothing pressure at each measurement part of commercial body shapers to provide basic information for product design and clothing pressure standard and level. This study used five body shaper. Clothing pressure measurements were taken at 18points: Anterior area 8points, lateral area 5points, posterior area 5points. The findings of this study were as follows. As a result of measuring the clothing pressure, the body shaper 1 showed the highest pressure, and body shaper 5 showed the lowest pressure at almost of the measurement points of the three body types. In some cases, body shapers 2, 3, and 4 showed different orders of pressure depending on the measurement point. The highest measured values in most body shapers were the P1 shoulder area and the P2 bust area. The lowest measurement area differed by body type, but mainly P3 underbust area, P4 thorax area and P9 axillary area, P11 waist lateral area, P13 hip lateral area. These body shapers showed different results depending on the the manufacturers and body type of middle-aged women, and because there was no standard for the pressure value. Therefore, it is necessary to design a body shaper sizing system after accurately setting the clothing pressure value for each body part of the consumer.
Abstract
This study measured and analyzed clothing pressure at each measurement part of commercial body shapers to provide basic information for product design and clothing pressure standard and level. This study used five body shaper. Clothing pressure measurements were taken at 18points: Anterior area 8points, lateral area 5points, posterior area 5points. The findings of this study were as follows. As a result of measuring the clothing pressure, the body shaper 1 showed the highest pressure, and body shaper 5 showed the lowest pressure at almost of the measurement points of the three body types. In some cases, body shapers 2, 3, and 4 showed different orders of pressure depending on the measurement point. The highest measured values in most body shapers were the P1 shoulder area and the P2 bust area. The lowest measurement area differed by body type, but mainly P3 underbust area, P4 thorax area and P9 axillary area, P11 waist lateral area, P13 hip lateral area. These body shapers showed different results depending on the the manufacturers and body type of middle-aged women, and because there was no standard for the pressure value. Therefore, it is necessary to design a body shaper sizing system after accurately setting the clothing pressure value for each body part of the consumer.
참고문헌 (17)
- Choi, H. S., "Technical wear design" (2003), Soohaksa
- 도월희, "중년 여성 복부 돌출 정도에 따른 토르소 형태 분류", 한국의류산업학회지, 23(2), pp.226~236 (2021), 한국의류산업학회
- 황혜민, "컨조인트 분석을 통한 기능성 보정속옷의 상품개발전략에 대한 연구", 석사, 패션마케팅ㆍ의상심리학, pp.2010
- 정연희, "인체의 3차원 스캔 데이터를 이용한 밀착 바디 슈트 개발", 한국생활과학회지, 15(3), pp.481~490 (2006), 한국생활과학회
- Jin, Z., "Study on the model of men’s upper body pressure and comfort sense - Based on the seamless underwear’s upper parts", 2009 International Joint Conference on Artificial Intelligence, pp.363~366 (2009)
- Kim, H. E., "The clothing pressure of the bodysuits on various sizes and movements", Journal of The Korean Society of Living Environmental System, 1(2), pp.129~138 (1994)
- Kim, H. K., "A study on functional foundatin purchase and wearing state by adult woman’s body cathexis", master, pp.2002
- Kim, H. K., "Clothing ergonomics experimental methodology" (2001), Kyomoonsa
- 김남임, "시판 체형보정용 파운데이션이 중년여성의 혈류 및 착용 쾌적감에 미치는 영향", 한국의류학회지, 45(3), pp.495~509 (2021), 한국의류학회[DOI]
- 김소영, "3차원 데이터를 활용하여 시니어를 대상으로 한 바디쉐이퍼의 보정기능성 평가", 한국의류산업학회지, 21(2), pp.856~866 (2019), 한국의류산업학회[DOI]
- "The 6th anthropometric dimension data" (2010)[URL]
- Lee, J. O., "A study on body satisfaction and wearing state of foundation among middle aged women", Journal of the Korean Society of Costume, 43, pp.83~96 (1999)
- 이영재, "중년 여성의 신체이미지에 따른 기능성 파운데이션 제품의 디자인 선호 실태", 한국디자인문화학회지, 12(1), pp.119~131 (2006), 한국디자인문화학회
- "Shapewear market size, share & trends analysis report by end user(male, female), by distribution channel(hypermarkets & supermarkets, specialty stores, online), by region, and segment forecasts, 2021-2028" (2021)[URL]
- Tamura, T., "The science of clothing environment" (2004), Kenpakusha
- Park, M. Y., "A study of Korean consumers’ purchase behavior of functional underwear", master, pp.2006
- Wang, Y., "The pressure comfort sensation of female's body parts caused by compression garment", Proceedings of the AHFE 2017 International Conference on Advances in Human Factors and Wearable Technologies, pp.94~104 (2018), Springer