서스펜션 진공 플라즈마 용사법을 통한 YSZ 코팅의 형성
Formation of YSZ Coatings Deposited by Suspension Vacuum Plasma Spraying
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
As increasing thermal efficiency of the gas turbine, the performance improvement of thermal barrier coatings is also becoming important. Ytrria stabilized zirconia(YSZ) is the most popular materials for ceramic top coating because of its low thermal conductivity. In order to enhance the performance of thermal barrier coatings for hot sections in the gas turbine, suspension plasma spraying was developed in order to feed nano-sized powders. YSZ coatings formed by suspension plasma spraying showed better performance than YSZ coatings due to its exclusive microstructure. In this research, two YSZ coatings were deposited by suspension vacuum plasma spraying at 400 mbar and 250 mbar. Microstructures of YSZ coatings were analyzed by scanning electron image(SEM) on each spraying conditions, respectively. Crystalline structure transformation was not detected by X-ray diffraction. Thermal conductivity of suspension vacuum plasma sprayed YSZ coatings were measured by laser flash analysis. Thermal conductivity of suspension vacuum plasma sprayed YSZ coatings containing horizontally oriented nano-sized pores and vertical cracks showed 0.6-1.0 W/m·K, similar to thermal conductivity of YSZ coatings formed by atmospheric plasma spraying.
Abstract
As increasing thermal efficiency of the gas turbine, the performance improvement of thermal barrier coatings is also becoming important. Ytrria stabilized zirconia(YSZ) is the most popular materials for ceramic top coating because of its low thermal conductivity. In order to enhance the performance of thermal barrier coatings for hot sections in the gas turbine, suspension plasma spraying was developed in order to feed nano-sized powders. YSZ coatings formed by suspension plasma spraying showed better performance than YSZ coatings due to its exclusive microstructure. In this research, two YSZ coatings were deposited by suspension vacuum plasma spraying at 400 mbar and 250 mbar. Microstructures of YSZ coatings were analyzed by scanning electron image(SEM) on each spraying conditions, respectively. Crystalline structure transformation was not detected by X-ray diffraction. Thermal conductivity of suspension vacuum plasma sprayed YSZ coatings were measured by laser flash analysis. Thermal conductivity of suspension vacuum plasma sprayed YSZ coatings containing horizontally oriented nano-sized pores and vertical cracks showed 0.6-1.0 W/m·K, similar to thermal conductivity of YSZ coatings formed by atmospheric plasma spraying.
참고문헌 (14)
- Haynes, J.A., "Characterization of alumina scales formed during isothermal and cyclic oxidation of plasmasprayed TBC systems at 1150oC", Oxidation of Metals, 52(1), pp.31~76 (1999)
- Khan, A.N., "Behavior of air plasma sprayed thermal barrier coatings, subject to intense thermal cycling", Surf. and Coat. Tech, 166(1), pp.37~43 (2003)
- Smialek, J.L., "Compiled furnace cyclic lives of EB-PVD thermal barrier coatings", Surf. and Coat. Tech., 276, pp.31~38 (2015)
- Sohn, Y.H., "Thermal cycling of EB-PVD", MCrAlY thermal barrier coatings: I. Microstructural development and spallation mechanisms, 2001, pp.146-147, 70~78
- Mušálek, R., "Feasibility of suspension spraying of yttria-stabilized zirconia with waterstabilized plasma torch", Surf. and Coat. Tech., 268, pp.58~62 (2015)
- Mahade, S., "Thermal conductivity and thermal cyclic fatigue of multilayered Gd2Zr2O7", YSZ thermal barrier coatings processed by suspension plasma spray, 2015, pp.283, 329~336
- M. V. Swain, "Thermal diffusivity, heat capacity and thermal conductivity of porous partially stabilized zirconia", J. Mater. Sci. Lett., 5(8), pp.799~802 (1986)
- Bertrand, G., "Low conductivity plasma sprayed thermal barrier coating using hollow psz spheres:Correlation between thermophysical properties and microstructure", Surf. and Coat. Tech., 202, pp.1994~2001 (2008)
- D. Schwingel, "Mechanical and thermophysical properties of thick PYSZ thermal barrier coatings:correlation with microstructure and spraying parameters", Surf. and Coat. Tech., 108-109, pp.99~106 (1998)
- S. Sampath, "Thermal Sprayed Ceramic Coatings:Fundamental Issues and Application Considerations", Int. J. Mater. Product Technol., 35(4), pp.425~448 (2009)
- G. Antou, "Evaluation of Modifications Induced on Pore Network and Structure of Partially Stabilized Zirconia Manufactured by Hybrid Plasma Spray Process", Surf. Coat. Tech., 180-181, pp.627~632 (2004)
- C.A. Johnson, "Relationships Between Residual Stress, Microstructure and Mechanical Properties of Electron Beam-Physical Vapor Deposition Thermal Barrier Coatings", Surf. Coat. Tech, 108-109, pp.80~85 (1998)
- P. Bengtsson, "Characterization of Micro-structural Defects in Plasma-Sprayed Thermal Barrier Coatings", J. Therm. Spray Tech., 4(3), pp.245~251 (1995)
- Y. Tan, "Optimizing Compliance and Thermal Conductivity of Plasma Sprayed Thermal Barrier Coatings via Controlled Powders and Processing Strategies", J. Therm. Spray Tech, 21(5), pp.950~962 (2012)