ETFE 필름을 적용한 태양광 모듈의 전기적 출력 및 신뢰성에 관한 연구
Electrical Output and Reliability of Photovoltaic Module Using Ethylene Tetrafluoroethylene Film
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
As the supply of photovoltaic (PV) increases worldwide, the cumulative installations in 2018 were 7.9 and 560 GW in Korea and the world, respectively. Typically, when the ground on commercial PV modules is installed, the area is limited; hence, new designs of PV modules are required to install additional PVs. Among the new design of PV modules, lightweight PV modules can be utilized in PV systems, such as buildings, farmlands, and floating PV. Concerning the investigation of lightweight PV modules, several studies on materials for replacing low-iron tempered glass, which comprises approximately 65% of the PV module weight, have been conducted. However, materials that are used as substitutes for glass should possess similar lightweight properties and reliability as glass. In this study, experimental tests were performed to evaluate the applicability of ethylene tetrafluoroethylene (ETFE) film with excellent resistance to water and aging as a front material of PV modules. The transmittance and ultraviolet properties of the ETFE film were determined and compared with those of glass. A 1-cell module and laboratory-scale 24-cell module were manufactured using the ETFE film and glass, and the electrical output was measured and analyzed. Furthermore, damp heat and thermal cycle tests were conducted to evaluate the reliability of the ETFE film module. Based on the experimental results, the electrical output and reliability of the ETFE film module were similar to those of the glass module, and the ETFE film could be used as the front material of PV modules.
Abstract
As the supply of photovoltaic (PV) increases worldwide, the cumulative installations in 2018 were 7.9 and 560 GW in Korea and the world, respectively. Typically, when the ground on commercial PV modules is installed, the area is limited; hence, new designs of PV modules are required to install additional PVs. Among the new design of PV modules, lightweight PV modules can be utilized in PV systems, such as buildings, farmlands, and floating PV. Concerning the investigation of lightweight PV modules, several studies on materials for replacing low-iron tempered glass, which comprises approximately 65% of the PV module weight, have been conducted. However, materials that are used as substitutes for glass should possess similar lightweight properties and reliability as glass. In this study, experimental tests were performed to evaluate the applicability of ethylene tetrafluoroethylene (ETFE) film with excellent resistance to water and aging as a front material of PV modules. The transmittance and ultraviolet properties of the ETFE film were determined and compared with those of glass. A 1-cell module and laboratory-scale 24-cell module were manufactured using the ETFE film and glass, and the electrical output was measured and analyzed. Furthermore, damp heat and thermal cycle tests were conducted to evaluate the reliability of the ETFE film module. Based on the experimental results, the electrical output and reliability of the ETFE film module were similar to those of the glass module, and the ETFE film could be used as the front material of PV modules.
참고문헌 (16)
- Snapshot of global photovoltaic markets, "PVPS, I.", ~, pp.Report IEA PVPS T1-33 (2018)
- Kaltenbrunner, M., "Ultrathin and Lightweight Organic Solar Cells with High Flexibility", Nature Communications, 3(1), pp.1~7 (2012)
- Housser, G., "Lightweight, Zero-Penetration, Pre-Formed Support Molds Adapted for Rigid Thin-Film Solar Modules", 2015 IEEE 42nd Photovoltaic Specialist Conference (PVSC), pp.1~4 (2015), IEEE
- Vygranenko, Y., "Lightweight Amorphous Silicon Photovoltaic Modules on Flexible Plastic Substrate", Canadian Journal of Physics, 92(7, pp.8) (2014), 871~874
- Izu, M., "Lightweight flexible rooftop PV module", Proceedings of 1994 IEEE 1st World Conference on Photovoltaic Energy Conversion-WCPEC (A Joint Conference of PVSC, PVSEC and PSEC), 1, pp.990~993 (1994), IEEE
- Halbe, A., "Evaluation of Mounting Mechanisms for the Installation of Lightweight PV Systems on Commercial Rooftops", 2014 IEEE 40th Photovoltaic Specialist Conference (PVSC), pp.3539~3542 (2014), IEEE
- Honeker, C., "Reducing Installed Costs of Residential Solar by the use of Adhesive Mounted Lightweight Solar Modules", 2016 IEEE 43rd Photovoltaic Specialists Conference (PVSC), pp.3135~3140 (2016), IEEE
- Martins, A. C., "Robust Glass-Free Lightweight Photovoltaic Modules With Improved Resistance to Mechanical Loads and Impact", IEEE Journal of Photovoltaics, 9(1), pp.245~251 (2018)
- Martins, A. C., "Thermo-Mechanical Stability of Lightweight Glass-Free Photovoltaic Modules Based on a Composite Substrate", Solar Energy Materials and Solar Cells, 187, pp.82~90 (2018)
- Holton, E., "Cost and Market Analysis of Integrative Lightweight PV Systems for Low-Slope Commercial Rooftops", 2014 IEEE 40th Photovoltaic Specialist Conference (PVSC), pp.2740~2742 (2014), IEEE
- Metacarpa, D., "Reduced Balance of System Costs using Lightweight Photovoltaics Integrated with Roofing Material Membranes", 2015 IEEE 42nd Photovoltaic Specialist Conference (PVSC). IEEE (2015)
- Cremers, J., "Comparative Study of a New Ir-Absorbing Film to Improve Solar Shading and Thermal Comfort for ETFE structures", Procedia Engineering, 155, pp.113~120 (2016)
- Menéndez, A., "A Multifunctional ETFE Module for Sustainable Façade Lighting: Design, Manufacturing and Monitoring", Energy and Buildings, 161, pp.10~21 (2018)
- Kang, G. H., "Photovoltaic Module", Sungandang
- 임종록, "고분자 보호 필름을 적용한 태양광 모듈의 출력 및 신뢰성에 관한 연구", 한국태양에너지학회 논문집, 39(5), pp.1~10 (2019), 한국태양에너지학회[DOI]