CoCr 기반 합금의 초기 마모 특성에 대한 정량적 평가
Quantitative Assessment of Initial Wear Characteristicsof CoCr-Based Alloys
0
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
CoCr-based alloys have been developed as wear-resistant materials owing to their excellent mechanical properties and strong wear resistance. The purpose of this study is to experimentally assess the frictional and wear characteristics of CoCr-based alloys slid against two different counter materials subjected to various normal forces to determine the expansion applicability of CoCr-based alloys. CoCrMo and CoCr alloys were selected as the target materials and NiCr and NiCrB alloys as counter materials. Experimental tests were performed using a pin-on-reciprocating plate tribo-tester under dry lubrication. Before performing the tests, the surface of the specimens was observed through confocal microscopy and the hardness was measured using a micro-Vickers hardness tester. The wear volume of the plate was calculated at the end of the tests using confocal microscope data, and the wear rate was quantitatively obtained based on Archard's wear law. From the results, the wear rates of the CoCrMo specimens that slid against NiCr and NiCrB are 7.69 × 10-6 mm3/Nm and 5.26 × 10-6 mm3/Nm, respectively. The wear rates of the CoCr specimens that slid against NiCr and NiCrB were higher than those of the CoCrMo specimens by factors of approximately 4 and 8, respectively. The CoCrMo specimens further exhibited lower friction characteristics than the CoCr specimens. The findings of this study will be useful for expanded applications of CoCr-based alloys as wear-resistant materials for various mechanical parts.
Abstract
CoCr-based alloys have been developed as wear-resistant materials owing to their excellent mechanical properties and strong wear resistance. The purpose of this study is to experimentally assess the frictional and wear characteristics of CoCr-based alloys slid against two different counter materials subjected to various normal forces to determine the expansion applicability of CoCr-based alloys. CoCrMo and CoCr alloys were selected as the target materials and NiCr and NiCrB alloys as counter materials. Experimental tests were performed using a pin-on-reciprocating plate tribo-tester under dry lubrication. Before performing the tests, the surface of the specimens was observed through confocal microscopy and the hardness was measured using a micro-Vickers hardness tester. The wear volume of the plate was calculated at the end of the tests using confocal microscope data, and the wear rate was quantitatively obtained based on Archard's wear law. From the results, the wear rates of the CoCrMo specimens that slid against NiCr and NiCrB are 7.69 × 10-6 mm3/Nm and 5.26 × 10-6 mm3/Nm, respectively. The wear rates of the CoCr specimens that slid against NiCr and NiCrB were higher than those of the CoCrMo specimens by factors of approximately 4 and 8, respectively. The CoCrMo specimens further exhibited lower friction characteristics than the CoCr specimens. The findings of this study will be useful for expanded applications of CoCr-based alloys as wear-resistant materials for various mechanical parts.
참고문헌 (14)
- Hulwan, D. B., "Performance, Emission and Combustion Characteristic of a Multicylinder DI Diesel Engine Running on Diesel–Ethanol–Biodiesel Blends of High Ethanol Content", Appl. Energy, 88, pp.5042~5055 (2011)
- Xu, G, Jia, M., "Potential of Reactivity Controlled Compression Ignition(RCCI)Combustion Coupled with Variable Valve Timing(VVT)Strategy for Meeting Euro 6 Emission Regulations and High Fuel Efficiency in a Heavy-Duty Diesel Engine", Energy Conv. Manag, 171, pp.683~698 (2018)
- Kim, K. S., "A Study on Development of High Pressure Fuel Injection Pump for Marine Diesel Engine", Proc. Summer Conf. Korean Soc. Fluid Mach, pp.423~424 (2018)
- 구현호, "선박 엔진의 실린더 라이너용 합금주철의 부식마멸에 미치는 분위기의 영향", 한국트라이볼로지학회지, 28(5), pp.233~239 (2012), 한국트라이볼로지학회[DOI]
- Renz, A., "High-temperature Sliding Wear Behaviour of Stellite®12and Tribaloy®T400", Wear, 402-403, pp.148~159 (2018)
- Pugacheva, N. B., "Studying the Structure and Micromechanical Properties of a Hardfaced Wear-Resistant Coating", Proc. AIP Conf (2018)
- A. Halstead, "Structure and hardness of Co–Mo–Cr–Si wear resistant alloys (Tribaloys)", Metal Science, 18(10), pp.491~500 (2013), Maney Publishing[DOI]
- Motallebzadeh, A., "Microstructure and Tribological Properties of PTA Deposited Stellite 12 Coating on Steel Substrate", Manuf. Sci. Technol, 3, pp.224~228 (2015)
- Luo, H. L., "Abrasive Wear Comparison of Cr3C2", Ni3Al Composite and Stellite 12 Alloy Cladding, 2007, pp.14, 15~20
- Du, H. L., "Microscopy of Wear Affected Surface Produced During Sliding of Nimonic 80A Against Stellite 6 at 20°C", Mater. Sci. Eng. A, 357, pp.412~422 (2003)
- Chin, C. H., "Sliding wear Performance of Fe-, Ni-and Co-based Hardfacing Alloys for PTA cladding", Int. J. Mater. Res, 104, pp.293~300 (2013)
- Kim, D. K., "Application of Nimonic 80A to the Hot forging of an Exhaust Valve Head", J. Mater. Process. Technol, 113, pp.148~152 (2001)
- Davis, J, R., "Nikel, Cobalt, and Their Alloys", pp.129~ (2000), ASM International
- Nascimento, E. M., "Characterization and Wear of Oxides Formed on CoCrMoSi Alloy Coatings", Surf. Coat. Technol, 332, pp.408~413 (2017)