SUJ2 베어링 강의 트라이볼로지 특성에 대한 초음파나노표면개질 (UNSM) 및 원더프로세스크래프트 (WPC) 처리 효과 연구
A Study on the Effects of Ultrasonic Nanocrystal SurfaceModification (UNSM) and Wonder Process Craft (WPC)Treatments on Tribological Properties of SUJ2 Bearing Steel
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Mechanical surface treatment is an excellent approach widely used to modulate and improve the performance and service life of bearings, gears, and frictional joints. The main purpose of this study is to investigate and compare the effect of ultrasonic nanocrystal surface modification (UNSM) and wonder process craft (WPC) on the surface and tribological properties of SUJ2 bearing steel. The surface roughness and hardness of the untreated and treated (UNSM- and WPC-treated) specimens were measured and compared. Their tribological properties were evaluated using a micro-tribometer under grease-lubricated and dry conditions against itself. Surface hardness measurement results revealed that both the UNSM- and WPC-treated specimens had a higher hardness than that of the untreated specimen. The surface roughness of the untreated specimen was reduced after UNSM and WPC treatments. Abrasive wear mode was observed on the surface of the specimens worn under grease-lubricated conditions, while adhesive wear mode was found on the surface of the specimens worn in dry conditions. According to the tribological test results, the friction coefficient and wear rate of the untreated specimens were reduced by the application of both the UNSM and WPC treatments under grease-lubricated and dry conditions.
Abstract
Mechanical surface treatment is an excellent approach widely used to modulate and improve the performance and service life of bearings, gears, and frictional joints. The main purpose of this study is to investigate and compare the effect of ultrasonic nanocrystal surface modification (UNSM) and wonder process craft (WPC) on the surface and tribological properties of SUJ2 bearing steel. The surface roughness and hardness of the untreated and treated (UNSM- and WPC-treated) specimens were measured and compared. Their tribological properties were evaluated using a micro-tribometer under grease-lubricated and dry conditions against itself. Surface hardness measurement results revealed that both the UNSM- and WPC-treated specimens had a higher hardness than that of the untreated specimen. The surface roughness of the untreated specimen was reduced after UNSM and WPC treatments. Abrasive wear mode was observed on the surface of the specimens worn under grease-lubricated conditions, while adhesive wear mode was found on the surface of the specimens worn in dry conditions. According to the tribological test results, the friction coefficient and wear rate of the untreated specimens were reduced by the application of both the UNSM and WPC treatments under grease-lubricated and dry conditions.
참고문헌 (10)
- "Encyclopedia of Tribology" (2013)[URL]
- Cao, J, "A Review of Surface Treatments for Sliding Bearings Used at Different Temperatures", Friction, Lubrication and Wear (2018)[DOI]
- Ma, Y, "Friction and wear behaviour of steel with bionic non-smooth surfaces during sliding", Mater. Sci. Technol (2016)[DOI]
- K. Y. Mohd Iqbal, "Surface Texturing for Low Friction Mechanical Components", 한국트라이볼로지학회지, 31(6), pp.287~293 (2015), 한국트라이볼로지학회[DOI]
- Uddin, G. M, "Experimental study of tribological and mechanical properties of TiN coating on AISI 52100 bearing steel", Advan. Mech. Eng (2018)[DOI]
- Oses, J, "Development of new duplex treatments on 100Cr6 steel combining thermochemical treatments, Laser Shock Peening and Physical Vapour Deposition", J. Phys. : Conf. Ser, 843, pp.012080~ (2017)[DOI]
- 카림바예프 루슬란, "표면개질 기술에 의한 Cu 기반 바이메탈의 인장강도,스크래치 저항성 및 트라이볼로지 성능 향상", 한국트라이볼로지학회지, 37(3), pp.83~90 (2021), 한국트라이볼로지학회[DOI]
- Nabipour, M, "A study of the effect of a surface treatment on the performance of cemented carbide inserts", MSc, pp.2019
- Armstrong, R.W, "60 Years of Hall-Petch: Past to Present Nano-scale Connections", Mater. Trans (2014)
- Behrens, B. A, "Wear investigation of selective α-Fe2O3 oxide layers generated on surfaces for dry sheet metal forming", Procedia Manuf, 15, pp.923~930 (2018)