선형절삭시험에 의한 슬림 코니컬커터의 절삭성능 평가(II): Skew Angle 변화에 의한 결과
Performance estimation of conical picks with slim design by the linear cutting test (II): depending on skew angle variation
0
조회
0
다운로드
10
인용
0
참고문헌
키워드
초록
본 연구에서는 받음각이 45°인 경우에 대해 사각이 0°와 6°이고 S/d비가 1.3~12사이인 시험조건에 대해 슬림 코니컬커터를 사용하여 선형절삭시험동안 발생하는 커터작용력을 측정하였다. 각 시험조건에서 커터작용력인 연직력, 절삭력, 구동력을 측정하였고 그 측정결과의 평균값을 사용하여 분석을 실시하였다. 커터관입깊이가 깊어질수록 비에너지가 감소하였고 커터관입깊이에 따른 커터작용력의 변화는 사각이 6°인 경우가 작게 나타났다. 이와 같은 결과로부터 사각이 6°인 경우가 0°인 경우에 비해 장비설계측면에서 효과적인 것으로 판단된다. 또한 Fc/Fn은 사각이 6°일 때가 0°인 경우에 비해 작게 나타났다. 그러나 사각이 있을 경우 구동력의 증가가 나타날 수 있으므로 이에 대한 고려가 필요하다.
Abstract
In this study, the cutter acting forces were measured by 3-directional load cell at two different skew angles and various S/d ratios during a series of linear cutting tests using a slim conical pick. The analysis for cutting performance were carried out after calculating average values of the measured results. The increase of penetration depth results in the decrease of specific energy. And the variations of the cutter acting forces depending on penetration depth in the case of 6 degree skew angle were smaller than in the case of 0 degree skew angle. From this results, 6 degree skew angle is more effective than 0 degree skew angle in designing optimal specifications of cutting head. In addition, Fc/Fn under the setting of 6 degree skew angle was smaller than under the setting of 0 degree skew angle. However, it should be considered that the increase of cutter acting force in the cutting direction accompanied the increase of driving force in the case of the setting for 6 degree skew angle.
참고문헌 (16)
- Asbury, B, "Design methodology, testing and evaluation of a continuous miner cutterhead for dust reduction in underground coal mining", 2002 SME Annual Meeting, pp.1~8 (2002)
- Balci, C, "Estimation of optimum specific energy based on rock properties for assessment of roadheader performance", The Journal of The South African Institute of Mining and Metallurgy, pp.633~642 (2004)
- Bilgin, N, "Cutting performance of rock hammers and roadheaders in Istanbul Metro drivages", Proceedings, Word Tunnel Congress'97, pp.455~460 (1997)
- Copur, H, "Field and laboratory studies on natural stones leading to empirical performance prediction of chain saw machines", International Journal of Rock Mechanics & Mining Sciences, 48, pp.269~282 (2011)
- 장수호, "암석의 선형절삭실험에 의한 디스크커터의 변형특성 평가", 한국터널지하공간학회 논문집, 14(3), pp.197~213 (2012), 사단법인 한국터널지하공간학회[DOI]
- 최순욱, "선형절삭실험 중 디스크커터 축에 작용하는 하중과 온도에 대한 실험적 연구", 한국터널지하공간학회 논문집, 15(3), pp.237~251 (2013), 사단법인 한국터널지하공간학회
- 최순욱, "선형절삭시험에 의한 더블디스크커터와 싱글디스크커터의 커터 작용력과 축응력에 대한 실험적 평가", 한국터널지하공간학회 논문집, 16(2), pp.181~191 (2014), 사단법인 한국터널지하공간학회[DOI]
- Fowell, R. J, "A comparison of dust make and energy requirements for rock cutting tools", International Journal of Mining Engineering, 2, pp.73~83 (1984)
- Gertsch, R, "Disc cutting tests in colorado red granite: implications for TBM performance prediction", International Journal of Rock Mechanics & Mining Sciences, 44, pp.238~246 (2007)
- Goktan, R. M, "A semi-empirical approach to cutting force prediction for pointattack picks", The Journal of The South African Institute of Mining and Metallurgy, 105, pp.257~264 (2005)
- Hurt, K. G, "Point attack tools:an evaluation of function and use for rock cutting", Mining Engineer, 140, pp.673~675 (1981)
- Kim, E, "Full scale linear cuttting experiment to examine conical bit rotation", Journal of Mining Science, 48(5), pp.882~895 (2012)
- Nilsen, B, "Hard rock tunnel boring prediction and field performance", Proc. of Rapid Excavation and Tunneliing Coference (RETC), pp.833~852 (1993)
- Rostami, J, "Application of heavy duty roadheaders for underground development of the yucca mountain exploratory study facility, high level radioactive waste management", Proceedings of the 5th Annual international conference, 2, pp.395~402 (1994)
- Cutterhead design procedures and performance evaluations for roadheader, "Rostami, J", Jamal Rostami Engineering Services LLC, ~ (2013)
- Tunnel Business Magazine, "Roadheaders in hard rock-east side access among north american projects employing roadheader technology", 20~21 (2011)