고강도 암반에서 수직구 기계굴착을 위한 연마재 워터젯 활용에 관한 연구
A study on the utilization of abrasive waterjet for mechanical excavation of hard rock in vertical shaft construction
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
TBM을 이용한 전력구 공사에서 수직구는 TBM 장비 및 전력선의 진출입을 위해 필수적인 구조물이다. 수직구는 지반을 수직으로 관통하여 굴착하기 때문에 암반을 굴착하는 경우가 많다. 암반 지반은 대부분 발파나 할암 공법을 적용하여 굴착하므로 이때 발생하는 소음 및 진동, 도로 점유로 인해 민원이 발생하고 있다. 따라서 기존 공법의 대안으로 기계식 굴착장비를 이용한 수직구 굴착을 고려하였다. 다만, 현 기술 수준에서 수직구 굴착장비는 암반의 압축강도 약 120 MPa 이상에서는 굴착성능이 현저히 저하되어 고강도 암반 지반 적용에 한계가 있다. 본 연구에서는 암반에서 기계식 굴착 성능 개선을 위해 연마재 워터젯 기술을 굴착 보조공법으로 활용하는 방안에 대해 검토하였다. 연마재 워터젯 절삭성능에 대한 검증을 위해 암석 절삭실험을 수행하고, 실험결과로부터 이격거리, 이송속도, 수압 조절을 통해 지반조건 변화에 대응하여 굴착성능을 확보하는 것이 적절할 것으로 판단하였다. 또한, 일축압축강도와 RQD, 굴진율의 관계를 이용하여 연마재 워터젯을 이용한 인위적인 절리생성을 통해 굴착성능을 향상시키는 방안을 제시하였다. 본 연구결과는 향후 수직구 기계식 굴착장비 도입을 위한 기초자료로 활용될 수 있을 것으로 기대된다.
Abstract
In cable tunnel construction using TBM, the vertical shaft is an essential structure for entrance and exit of TBM equipment and power lines. Since a shaft penetrates the ground vertically, it often encounters rock mass. Blasting or rock splitting methods, which are mainly used to the rock excavation, cause public complaints due to the noise, vibration and road occupation. Therefore, mechanical excavation using vertical shaft excavation machine are considered as an alternative to the conventional methods. However, at the current level of technology, the vertical excavation machine has limitation in its performance when applied for high strength rock with a compressive strength of more than 120 MPa. In this study, the potential utilization of waterjet technology as an excavation assistance method was investigated to improve mechanical excavation performance in the hard rock formations. Rock cutting experiments were conducted to verify the cutting performance of the abrasive waterjet. Based on the experimental result, it was found that ensuring excavation performance with respect to changing in ground conditions can be achieved by adjusting waterjet parameters such as standoff distance, traverse speed and water pressure. In addition, based on the relationship between excavation performance, uniaxial compressive strength and RQD, it was suggested that excavation performance could be improved by artificially creating joints using the abrasive waterjet. It is expected that these research results can be utilized as fundamental data for the introduction of vertical shaft excavation machines in the future.
참고문헌 (20)
- AASHTO, "Standard Specifications for Highway Bridges, 16th Edition", American Association of State Highway and Transportation Officials, 62~63 (1996)
- "Herrenknecht Home page" (2023)[URL]
- Kim, J. G., "A study on the driving performance of the microtunneling machine with a rotating water jet cutterhead", Proceedings of the Korea Institute of Information and Telecommunication Facilities Engineering Summer Conference, pp.367~372 (2003)
- Kim, Y. G., "Roadheader solution in urban tunneling", Geotechnical Engineering, 36(2), pp.6~16 (2020)
- Kulhawy, F. H., "Ground Engineer’s Reference Book", pp.1~13 (1987), Butterworths
- Liu, S., "Impact characteristics of rock breaking using a conical pick assisted with abrasive slurry jet", Engineering Fracture Mechanics, 271, pp.108647~ (2022)
- Liu, S., "Drilling performance of rock drill by high-pressure water jet under different configuration modes", Shock and Vibration, 2017, pp.1~14 (2017)[DOI]
- Luo, X., "Research on the hard rock cutting characteristics of disc cutter under front-mounted water jet precutting kerf conditions", Engineering Fracture Mechanics, 287, pp.109330~ (2023)
- Ocak, I., "Comparative studies on the performance of a roadheader, impact hammer and drilling and blasting method in the excavation of metro station tunnels in Istanbul", Tunnelling and Underground Space Technology, 25(2), pp.181~187 (2010)
- Oh, T. M., "Characterization of effective parameters in abrasive waterjet rock cutting", Rock Mechanics and Rock Engineering, 47, pp.745~756 (2014)
- 오태민, "워터젯 자유면을 이용한 암반발파 굴착공법의 효과", 한국터널지하공간학회 논문집, 15(1), pp.49~57 (2013), 사단법인 한국터널지하공간학회
- Oh, T. M., "Effect of garnet characteristics on abrasive waterjet cutting of hard granite rock", Advances in Civil Engineering, 2019, pp.1~12 (2019)[DOI]
- Oh, T. M., "Effect of abrasive feed rate on rock cutting performance of abrasive waterjet", Rock Mechanics and Rock Engineering, 52, pp.3431~3442 (2019)
- 오태민, "암석물성이 워터젯 암석절삭 성능에 미치는 영향고찰", 한국터널지하공간학회 논문집, 17(5), pp.533~551 (2015), 사단법인 한국터널지하공간학회
- Plinninger, R. J., "Abrasiveness assessment for hard rock drilling", Geomechanics and Tunnelling, 1(1), pp.38~46 (2008)
- 신종호, "터널라이닝 안전관리를 위한 발파제한영역 평가", 한국터널지하공간학회 논문집, 11(1), pp.85~96 (2009), 사단법인 한국터널지하공간학회
- Thuro, K. P. R. J., "Roadheader excavation performance-geological and geotechnical influences", Proceedings of the 9th ISRM Congress, pp.1241~1244 (1999)
- Zhang, J., "Using a high-pressure water jet-assisted tunnel boring machine to break rock", Advances in Mechanical Engineering, 12(10), pp.1~16 (2020)
- Zhang, L., "Estimating the strength of jointed rock masses", Rock Mechanics and Rock Engineering, 43, pp.391~402 (2010)
- Zhang, X., "Investigation of rock breaking mechanism with TBM hob under traditional and free-face condition", Engineering Fracture Mechanics, 242, pp.107432~ (2021)