FFF 3D 프린터를 이용한 DfAM 기반 소형선박용 스탠션 지속가능 개발 사례 연구
A Case Study on the Sustainability for a Stanchion of Recreational Crafts based on the Design for Additive Manufacturing Using a FFF-type 3D Printer
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this study, the 3D printing technique called design for additive manufacturing (DfAM) that is widely used in various industries was applied to marine leisure ships of equipment. The DfAM for the stanchion for crew safety was applied to the equipment used in an actual recreational craft. As design constraints, the design alternatives were not to exceed the safety and weight of the existing stainless steel material, which were reviewed, and the production of a low-cost FFF-type 3D printing method that can be used even in small shipyards was considered. Until now, additive manufacturing has been used for manufacturing only prototypes owing to its limitations of high manufacturing cost and low strength; however, in this study, it was applied to the mass production process to replace existing products. Thus, a design was developed with low manufacturing cost, adequate performance maintenance, and increased design freedom, and the optimal design was derived via structural analysis comparisons for each design alternative. In addition, a life-cycle assessment based on the ISO 1404X was conducted to develop sustainable products. Through this study, the effectiveness of additive manufacturing was examined for future applications in the shipbuilding industry.
Abstract
In this study, the 3D printing technique called design for additive manufacturing (DfAM) that is widely used in various industries was applied to marine leisure ships of equipment. The DfAM for the stanchion for crew safety was applied to the equipment used in an actual recreational craft. As design constraints, the design alternatives were not to exceed the safety and weight of the existing stainless steel material, which were reviewed, and the production of a low-cost FFF-type 3D printing method that can be used even in small shipyards was considered. Until now, additive manufacturing has been used for manufacturing only prototypes owing to its limitations of high manufacturing cost and low strength; however, in this study, it was applied to the mass production process to replace existing products. Thus, a design was developed with low manufacturing cost, adequate performance maintenance, and increased design freedom, and the optimal design was derived via structural analysis comparisons for each design alternative. In addition, a life-cycle assessment based on the ISO 1404X was conducted to develop sustainable products. Through this study, the effectiveness of additive manufacturing was examined for future applications in the shipbuilding industry.
참고문헌 (15)
- 현충민, "고주파 유도가열을 이용한 오목 곡면 곡가공에 관한 연구", 대한조선학회 논문집, 56(2), pp.128~134 (2019), 대한조선학회[DOI]
- Jang, C. D, "The optimum structural design of the high-speed surface effect ship using composite materials – minimum weight eesign", Journal of the Society of Naval Architects of Korea, 35(2), pp.94~103 (1998)
- Kazi, R. H, "Dream sketch : Early stage 3D design explorations with sketching and generative design", Proceedings of the 30th Annual ACM Symposium on User Interface Software and Technology, 14, 14, pp.401~414 (2017)
- 이동건, "복합재료 소형선박의 지속가능한 설계를 위한 전과정평가 사례 연구", 한국정밀공학회지, 34(11), pp.835~841 (2017), 한국정밀공학회
- Lee, D. K, "Simulation-based work plan verification in shipyards", Journal of Ship Production and Design, 30(2), pp.49~57 (2014)
- Lee, J, "Life cycle assessment and recycling for ships", Journal of the Society of Naval Architects of Korea, 43(1), pp.17~21 (2006)
- Xing Li, "A collaborative simulation in shipbuilding and the offshore installation based on the integration of the dynamic analysis, virtual reality, and control devices", International Journal of Naval Architecture and Ocean Engineering, 11(2), pp.699~722 (2019), 대한조선학회[DOI]
- Mackley, C.J, "Reducing costs and increasing productivity in ship maintenance using product lifecycle management, 3D Laser Scanning and 3D Printing", M.Sc, pp.2014
- 오대균, "CFRP 선체소재와 전기추진체계가 소형선박의 경량화에 미치는 효과", 해양환경안전학회지, 24(6), pp.818~824 (2018), 해양환경안전학회[DOI]
- Sarath C. Renjith, "A Design Framework for Additive Manufacturing: Integration of Additive Manufacturing Capabilities in the Early Design Process", International Journal of Precision Engineering and Manufacturing, 21(2), pp.329~345 (2020), 한국정밀공학회[DOI]
- 유철호, "선체 곡판 완성도 평가용 3차원 곡형의 제작 자동화를 위한 생산 정보 산출 시스템", 대한조선학회 논문집, 55(2), pp.136~143 (2018), 대한조선학회[DOI]
- "The impact of DfAM" (2018)[URL]
- 유동진, "Recent Trends and Challenges in Computer-Aided Design of Additive Manufacturing-based Biomimetic Scaffolds and Bioartificial Organs", International Journal of Precision Engineering and Manufacturing, 15(10), pp.2205~2217 (2014), 한국정밀공학회
- Zhou, M, "The COC algorithm, part II : Topological, geometrical and generalized shape optimization", Computer Methods in Applied Mechanics and Engineering, 89, pp.309~336 (1991)