수정된 후방 플로팅 링 실을 적용한 7톤급 터보펌프 산화제 펌프의 진동 및 압력 측정
Measurements of Vibration and Pressure of an Oxidizer Pump fora 7-tonf Turbopump with a Modified Rear Floating Ring Seal
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
In this paper, we present an experimental investigation of the frequency characteristics and a visual inspection of an oxidizer pump with a modified rear-floating ring seal for a 7-tonf turbopump. An oxidizer pump typically operates at high rotational speeds and under cryogenic conditions. Despite its low hydraulic efficiency, the floating ring seal is frequently employed as a leakage control solution for turbomachinery because it effectively reduces abrasion by friction. When the oxidizer pump starts up, the floating ring moves excursively but locks up stably against the pump casing when the contact pressure increases. The compressive force on the floating ring depends on the hydrodynamic forces induced by the flow through the floating ring. This force is controlled by the nose position of the floating ring. Based on a validation test for a 7-tonf turbopump with two types of floating rings, we concluded that the floating ring with a small diameter nose can move easily with a low contact pressure in the cooling path. This leads to instability of the pressure fluctuation around the floating ring. In contrast, a floating ring with a large diameter nose has a high contact pressure and attaches strongly to the casing, which causes wear and frictional oxidation between the contact surfaces of the impeller and the floating ring.
Abstract
In this paper, we present an experimental investigation of the frequency characteristics and a visual inspection of an oxidizer pump with a modified rear-floating ring seal for a 7-tonf turbopump. An oxidizer pump typically operates at high rotational speeds and under cryogenic conditions. Despite its low hydraulic efficiency, the floating ring seal is frequently employed as a leakage control solution for turbomachinery because it effectively reduces abrasion by friction. When the oxidizer pump starts up, the floating ring moves excursively but locks up stably against the pump casing when the contact pressure increases. The compressive force on the floating ring depends on the hydrodynamic forces induced by the flow through the floating ring. This force is controlled by the nose position of the floating ring. Based on a validation test for a 7-tonf turbopump with two types of floating rings, we concluded that the floating ring with a small diameter nose can move easily with a low contact pressure in the cooling path. This leads to instability of the pressure fluctuation around the floating ring. In contrast, a floating ring with a large diameter nose has a high contact pressure and attaches strongly to the casing, which causes wear and frictional oxidation between the contact surfaces of the impeller and the floating ring.
참고문헌 (14)
- Kim, J., "Current Status of Turbopump Development in Korea Aerospace Research Institute", International Astronautical Congress 2004 (2004)
- Huzel, D. K., "Modern Engineering for Design of Liquid-Propellant Rocket Engines" (1992), AIAA Press
- 곽현덕, "7톤급 액체로켓엔진용 터보펌프 조립체 성능시험", 한국추진공학회지, 19(2), pp.65~72 (2015), 한국추진공학회[DOI]
- 정은환, "75톤급 액체로켓엔진용 터보펌프 실매질 성능시험", 한국추진공학회지, 20(2), pp.86~93 (2016), 한국추진공학회[DOI]
- 최창호, "플로팅링 실 간극이 터보펌프용 펌프의 성능에 미치는 영향", 한국유체기계학회 논문집, 10(6), pp.38~43 (2007), 한국유체기계학회
- 김대진, "임펠러 및 플로팅 링 실이 원심 펌프의 성능에 미치는 영향", 대한기계학회논문집 B, 35(10), pp.1083~1088 (2011), 대한기계학회
- 안경민, "플러팅 링 실의 누설 특성에 관한 실험적 연구", 한국트라이볼로지학회지, 20(4), pp.183~189 (2004), 한국트라이볼로지학회
- 이용복, "액체 추진 로켓 터보 펌프용 플로팅 링 실에 대한 해석 및 실험 결과의 비교 연구", 한국유체기계학회 논문집, 7(6), pp.21~27 (2004), 한국유체기계학회
- 하태웅, "고압 터보 펌프 후로팅 링 실의 후로팅 링 거동 해석", 한국트라이볼로지학회지, 21(3), pp.122~129 (2005), 한국트라이볼로지학회
- 하태웅, "원형 단면 구멍 표면을 갖는 댐퍼 후로팅 링 실의 누설량 및 회전체 동역학적 특성 해석", 한국트라이볼로지학회지, 19(6), pp.349~356 (2003), 한국트라이볼로지학회
- Lee, Y. B., "Study on the Experiment of the Floating Ring Seal with Bump Foil for High Pressure Turbopump", J. Korean Soc. Tribol. Lubr. Eng, 22(2), pp.105~111 (2006)[DOI]
- Mariot, A., "Experimental Analysis of Floating Ring Annular Seals and Comparisons with Theoretical Predictions", ASME Journal of Engineering for Gas Turbines and Power, 138(4), pp.042503~ (2016)
- Peng Xia, "Lock-up characteristics of floating ring seals considering rotor whirling motion", Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 232(4), pp.437~452 (2018), SAGE Publications[DOI]
- Peng Xia, "Analysis of whirling motion for the dynamic system of floating ring seal and rotor", Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 233(8), pp.1221~1235 (2019), SAGE Publications[DOI]